Tape Manufacturing & Screening Module (TMM)

Tape Manufacturing & Screening Module (TMM)

 

 

 

SCSI Toolbox LLC is proud to announce the Tape Manufacturing Module addition to the STB Suite, joining a decade of real-world tape drive testing experience with input from hundreds of customers to bring the best new testing tool to the tape manufacturing and integration marketplace.

 

The Tape Manufacturing Module is the easiest to use, most versatile, and fastest tape testing product on the market. A true multi-threaded, multiple host bus adapter, multi-drive screening and testing tool, the Tape Manufacturing Module allows you to:

 

confirm that the proper drives are in the subsystem

download new drive firmware if needed

set compression on or off

log and track all error information

run any type of test, or sequence of tests at full bus and device speeds

run ANY external program as a part of the test sequence

log all process activities, drive information, and any errors to an Access database

create an individual text log file for each device tested

 

All processes and test sequences are created from a graphical user interface – no programming or scripting is required! Time from installation to a complete test process can be as little as 5 minutes!

 

Defining the Test Process

 

Test processes are divided into three sections, pre-test, test, and post-test.

 

Pre-Test

 

The pre-test process allows your test to screen the attached drives by the following qualifiers:

 

Drive Vendor – you can specify that a drive must match a certain vendor code, or the drive will be rejected from the test. Example = “QUANTUM”

 

Drive Product – you can specify that a drive must match a certain product code, or the drive will be rejected from the test. Example = “SDLT600”

 

Drive Firmware Version – you can specify that the firmware version of each drive must match a specified version. If the version does not match the drive under test the drive can either be rejected, or the proper firmware file can be downloaded into the drive.

 

Rewind All Drives – all drives can be rewound before the test sequence is started.

 

Set Compression On or Off – test with or without data compression enabled.

 

Clear Log Pages – all Log Page (error and performance) data can be cleared at the beginning of the test process.

 

Record Mode or Log Page data – all Mode and/or Log page data can be logged at the beginning of the test process.

 

During the test process, each drive will be individually checked against any or all of the above parameters.

The entire pre-test process definition is accomplished by using the simple GUI choices as show below:

 

 

 

Test Configuration

 

The test process will be made up of one or more test sequences. Each test sequence is defined by selecting test definition parameters from the Test Configuration Menu. Once a test is defined the test is added to the test sequence list.

 

The following tests can be used in a test sequence:

 

Type of Test

 

Write

Read

Write FileMark

Read FileMark

Rewind

Space Forward by Block

Space Forward by FileMark

Space Reverse by Block

Space Reverse by FileMark

Space to End Of Data

Turn Compression On

Turn Compression Off

Clear Log Pages

Save Log Pages

Synchronize

Run External Program

 

Data Patterns

 

13 data patterns are available

Data compare on read can be turned on or off

 

Test Duration

 

Read and Write tests can be selected to run for a specified time, or run until a specified amount of data has been transferred.

 

In the same manner as the pre-test conditions, tests are easily and quickly defined with the GUI as shown below – no editing, no syntax or language to learn, no way to make a mistake!

 

 

 

Device Selection

 

Drives to be tested are selected from a simple tree control. Any drive on any Host Bus Adapter (SCSI, Fibre Channel, ATAPI) can be selected for test.

 

Once drives are selected and the test process has begun, color-coded indicators show each drives status, and each drive may individually be:

 

Paused – pause the current test

Resume – resume the current test from where it was paused

Stop Current Test – stop the current test and proceed to the next test in the test sequence, if any

Stop All Tests – stop any further testing on the drive

Show Status – display the current test being run, the status of the test, performance and error statistics

 

Again, each drive can be individually controlled and monitored during the test process!

 

Here is an example of the current status of a drive under test:

 

 

 

The Fastest tape test/screening system available!

 

The Tape Manufacturing Module tests and configures each drive as if it were the only drive being tested. This means that as fast as a given drive/HBA combination will run, that is how quickly your test process will finish.

 

For instance, if you have two Ultra 320 HBA’s in your system, and one Ultra 160 HBA, the drives connected to the faster subsystem will not have to wait for the slower drives!

 

If you have a 5 step test sequence, the faster drives will finish each step and move on to the next as fast as they can, without waiting for the slower drives to finish!

 

If your business relies on processing as many drives as possible (as thoroughly as possible of course!) – the Tape Manufacturing Module will maximize your test process and your profits!

 

The Ultimate in reporting / data collecting

 

The Tape Manufacturing Module records every event that happens during the test process to an Access database. If you need to look at any part of your test process later down the road, the Tape Manufacturing Module has already collected all data for you. Detailed information on each drive tested (vendor, product, firmware version, mode page settings, what tests were run, test results, performance numbers, detailed error information) is all logged to a data base that can be accessed any way you would like.

 

In addition, and individual text file is created for each device tested. All test information and results are logged.

 

Need to include custom test methods?

 

The Tape Manufacturing Module allows you to synchronize all device tests, and to run any external program as a part of a test sequence. For example, you could:

– Control any brand of environmental/temperature chamber right from your test sequence

– Run an external program to access vendor unique factory log information during a test sequence

– Control a programmable power supply

– Send an email to notify a test event

 

But wait . . . there’s more!

 

All of the tests included in the Tape Manufacturing Module are accessible from our Developers Toolbox – so you can write your own tests using Visual Basic or Visual C++ and have instant access to our multi-threaded tape test library! So if you need to include high level tape tests into your existing or new test processes, our tests are just a few moments of programming away!

 

The most economical test solution

 

That equals a cost of zero! No extra charge at all when you buy the industry standard interactive test system, the STBSuite.

 

Being the industry leaders in SCSI and Fibre testing for the past decade, we are proud to bring our years of experience to a new focal point with the Tape Manufacturing Module.

 

We are familiar with the other products and solutions in the market, and we are confident that the Tape Manufacturing Module is by far the most superior product.

 

We guarantee that the Tape Manufacturing Module solution is the most

-versatile,

-easiest to use,

-fastest, and

-the best value

 

Protocol Support

 

SCSI (All interfaces – single-ended, differential, SCSI 1, 2, 3, wide or narrow devices, Ultra II, Ultra3)

Fibre Channel (FCAL)

Magneto Optical (MO)

Serial Attached SCSI (SAS)

iSCSI

Serial ATA (SATA)

ATAPI

 

Operating System Requirements

 

The SCSItoolbox Suite is available for the following platforms:

 

Windows XP SP2 or later (32 and 64bit)

Windows Server 2003 SP2 higher (32 and 64bit)

Windows Server 2008 (32 and 64bit)

Windows Vista (32 and 64bit)

Windows 7 (32 and 64bit)

Redhat Linux Kernel 2.6 or newer (API’s only)